|
Batteries replacement |
| Door sensor |
- Push the grooved tab inwards to release sensor from back cover.
- Remove the old batteries.
- Replace with two new CR2032 batteries.
- Attach the sensor to the back cover. It should snap in place.
|
| 2GIG motion sensor |
- To open motion sensor, remove the screw from bottom of the sensor and pull off the back cover.
- Remove the old battery.
- Replace with a new CR123A battery.
- Attach the sensor to the back cover and tighten screw.
|
| Honeywell motion sensor |
- To open motion sensor, push in tab at the bottom of the sensor and pull front of sensor away from the back cover.
- Remove the old battery.
- Replace with a new CR123A battery.
- Attach the sensor to the back cover and snap into place.
|
| Glass break sensor |
- To open the glass break sensor, turn the unit counter-clockwise to release it from the back cover.
- Remove the old batteries.
- Replace with two new CR123A batteries.
- Attach the sensor to the back cover and turn the unit clockwise to lock it into place.
|
| Wireless keypad |
- To open the wireless keypad, push the two tabs on the top side simultaneously and pull outwards.
- Remove the old batteries.
- Replace with two new CR2032 batteries.
- Attach the keypad back to the back cover and snap into place.
|
| Keyfob |
- To open the keyfob, unscrew the back and separate the two sides.
- Remove the old battery.
- Replace with a new CR2025 battery.
- Attach the two sides and secure them with the screw.
|
| Water sensor |
- To open the water sensor, push down the tab and pull the front cover off the back cover.
- Remove the old battery.
- Replace with a new CR15H270 or CR2 battery.
- Attach the sensor to the back cover and snap into place.
|
| Carbon monoxide (CO) detector |
- To open the CO detector, turn the unit counter-clockwise to release it from the back cover.
- Remove the old battery.
- Replace with a new CR123A battery.
- Attach the sensor to the back cover and turn the unit clockwise to lock it into place.
|
| 2GIG smoke detector |
- To open the smoke detector, turn the unit counter-clockwise to release it from the back cover.
- Remove the old batteries.
- Replace with three new AAA batteries.
- Attach the sensor to the back cover and turn the unit clockwise to lock it into place.
|
| Honeywell smoke detector |
- To open the smoke detector, turn the unit counter-clockwise to release it from the back cover.
- Remove the old battery.
- Replace with a new CR123A battery.
- Attach the sensor to the back cover and turn the unit clockwise to lock it into place.
|
| Wireless panic button |
- To open the panic button, separate the top cover by placing a flathead screwdriver in the slot on the bottom right corner, between the top and bottom cover, and twist.
- Place a small flathead screwdriver in the slot between the metal clip and the battery and twist the screwdriver slightly while holding back one of the black plastic edges holding the battery.
- Replace with a new CR2032 battery.
- Attach the front and back covers and snap into place.
|
| Image sensor |
- To open the image sensor, slide the image sensor upwards to detach it from the back plate/mount.
- Remove the old batteries.
- Replace with two new AA lithium batteries.
- Slide the sensor into the back plate/mount.
|
| Door lock |
- Remove three screws from the back cover (one on each side and one on the bottom).
- Remove the back cover.
- Pull out the battery tray from the top.
- Remove the old batteries.
- Replace with four new AA batteries.
- Slide the battery tray back in.
- Attach the back cover.
- Reinstall the screws to secure.
|
| Thermostat (GC-TBZ48) |
- Using fingernails at the indents on the cover bottom, pull open the front panel (the thin front cover, not the main panel).
- Remove the old batteries.
- Replace with four new AA batteries.
- Place the front cover back on and snap into place.
|
